{"product_id":"sparkfun-qwiic-quad-solid-state-relay-kit","title":"SparkFun Qwiic Quad Solid State Relay Kit","description":"\u003cp\u003eThe SparkFun Qwiic Quad Solid State Relay Kit takes one of our favorite \u003ca href=\"https:\/\/www.sparkfun.com\/products\/13015\"\u003esolid state relays\u003c\/a\u003e and lets you place up to four of them on a single PCB to control all of them via I\u003csup\u003e2\u003c\/sup\u003eC from your desired microcontroller. Each relay is rated to 40A @ 28-380 VAC so with all four on board you can control some serious power all from the easy-to-use Qwiic Connect System. The kit requires no soldering but there is some minor assembly required to attach the relays to the board and to connect your AC load.\u003c\/p\u003e \u003cp\u003eThe ATTiny84 on the board comes pre-programmed to accept various commands to toggle all four relays. The I\u003csup\u003e2\u003c\/sup\u003eC address of the ATTiny84 is software configurable so so if you had the desire and power, you could daisy chain over 100 Qwiic Quad Relays (but please be aware that toggling lots of relays on a 3.3V bus can cause voltage spikes so an external power supply will be required)! In addition, the address jumper can be opened to switch the I\u003csup\u003e2\u003c\/sup\u003eC address from 0x08 (Default) to 0x09 (Alternate).\u003c\/p\u003e \u003cp\u003eMessing with such high voltage is dangerous! This is a power accessory intended for users who are experienced around, and knowledgeable about, high AC voltage. If you're uncomfortable dealing with high AC voltage, that's okay! Check out the \u003ca href=\"https:\/\/www.sparkfun.com\/products\/14236\"\u003eIoT Power Relay\u003c\/a\u003e instead. The IoT Power Relay is fully enclosed, making it a lot safer. Also, for small loads (eg. 4-10A), air cooling should be sufficient but if you are sourcing more than that, a heat sink is highly recommended. Refer to the \u003ca href=\"https:\/\/cdn.sparkfun.com\/datasheets\/Components\/General\/SSR40DA.pdf\"\u003erelay datasheet\u003c\/a\u003e for recommended heat sink dimensions.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eNote:\u003c\/strong\u003e The black standoffs and 4-40 screws used to secure them shown in some of the photos are NOT included with the kit. Check out the Hookup Accessories below if you would like to include some in your order.\u003c\/p\u003e \u003chr\u003e \u003cp\u003e\u003cem\u003eThe SparkFun Qwiic connect system is an ecosystem of I\u003csup\u003e2\u003c\/sup\u003eC sensors, actuators, shields and cables that make prototyping faster and less prone to error. All Qwiic-enabled boards use a common 1mm pitch, 4-pin JST connector. This reduces the amount of required PCB space, and polarized connections mean you can�t hook it up wrong.\u003c\/em\u003e\u003c\/p\u003e \u003chr\u003e \u003cp\u003e\u003c\/p\u003e\u003cdiv class=\"center-block text-center\"\u003e \u003ca href=\"https:\/\/learn.sparkfun.com\/tutorials\/sparkfun-qwiic-quad-solid-state-relay-kit-hookup-guide\" class=\"btn btn-default\"\u003eGet Started with the SparkFun Qwiic Quad Solid State Relay Kit Guide\u003c\/a\u003e \u003c\/div\u003e \u003cp\u003e\u003cstrong\u003eIncludes:\u003c\/strong\u003e\u003c\/p\u003e \u003cul\u003e \u003cli\u003e1x Qwiic Quad Solid State PCB\u003c\/li\u003e \u003cli\u003e4x Solid State Relay - 40A (3-32V DC Input)\u003c\/li\u003e \u003cli\u003e8x 4-40 Hex Nut\u003c\/li\u003e \u003cli\u003e8x 3\/8in. Phillips Machine Screw - 4-40 Thread\u003c\/li\u003e \u003cli\u003eHook-up Wire 8\" - 22 AWG (Red)\u003c\/li\u003e \u003cli\u003eHook-up Wire 8\" - 22 AWG (Black)\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e \u003cul\u003e \u003cli\u003eOperating Voltage: 2.5-3.6V (3.3V recommended)\u003c\/li\u003e \u003cli\u003eI\u003csup\u003e2\u003c\/sup\u003eC Address: 0x08 (Default), 0x09 (Alternate via jumper)\u003c\/li\u003e \u003cli\u003eMax Current (Through Relay): 40A (24-380VAC)\u003c\/li\u003e \u003cli\u003eZero Cross Trigger\u003c\/li\u003e \u003cli\u003eNormally Open Circuit Only\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003e\u003cstrong\u003eDocuments:\u003c\/strong\u003e\u003c\/p\u003e \u003cul\u003e \u003cli\u003e\u003ca href=\"https:\/\/cdn.sparkfun.com\/assets\/learn_tutorials\/1\/1\/8\/6\/SparkFun_Qwiic_Quad_Solid_State_Relay-Schematic.pdf\"\u003eSchematic\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/cdn.sparkfun.com\/assets\/learn_tutorials\/1\/1\/8\/6\/Qwiic_Quad_Solid_State_Relay-EagleFiles.zip\"\u003eEagle Files\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/cdn.sparkfun.com\/r\/600-600\/assets\/learn_tutorials\/1\/1\/8\/6\/Qwiic_Quad_Solid_State_Relay-Dimensions.png\"\u003eBoard Dimensions\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/learn.sparkfun.com\/tutorials\/sparkfun-qwiic-quad-solid-state-relay-kit-hookup-guide\"\u003eHookup Guide\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\n\u003ca href=\"https:\/\/cdn.sparkfun.com\/datasheets\/Components\/General\/SSR40DA.pdf\"\u003eDatasheet\u003c\/a\u003e (Relay)\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/www.sparkfun.com\/qwiic\"\u003eQwiic Resource Page\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/github.com\/sparkfun\/SparkFun_Qwiic_Relay_Arduino_Library\"\u003eArduino Library\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\n\u003ca href=\"https:\/\/github.com\/sparkfun\/Qwiic_Relay_Py\"\u003ePython Package\u003c\/a\u003e \u003cul\u003e \u003cli\u003e\u003ca href=\"https:\/\/sparkfun-qwiic-relay.readthedocs.io\/en\/latest\/?\"\u003eReadtheDocs\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e\n\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/github.com\/sparkfun\/Qwiic_Quad_Solid_State_Relay\"\u003eHardware GitHub Repository\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003e\u003cstrong\u003eVideos\u003c\/strong\u003e\u003c\/p\u003e \u003cdiv class=\"flex-video-wrap clearfix\"\u003e \u003cdiv class=\"flex-video widescreen img\"\u003e \u003ciframe src=\"https:\/\/www.youtube.com\/embed\/1jAxJJCdTE0\/?autohide=1\u0026amp;border=0\u0026amp;wmode=opaque\u0026amp;enablejsapi=1\" frameborder=\"0\" allowfullscreen width=\"560\" height=\"315\"\u003e\u003c\/iframe\u003e \u003c\/div\u003e \u003c\/div\u003e\u003cbr\u003eAll product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them.","brand":"sparkfun-10","offers":[{"title":"Default Title","offer_id":32574053220437,"sku":"16833:KIT-16833:spark","price":8065.0,"currency_code":"INR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1034\/1611\/products\/16833-SparkFun_Qwiic_Quad_Solid_State_Relay_Kit-01.jpg?v=1595251057","url":"https:\/\/www.tanotis.com\/products\/sparkfun-qwiic-quad-solid-state-relay-kit","provider":"Tanotis","version":"1.0","type":"link"}