{"product_id":"sparkfun-mikroe-driver-click","title":"SparkFun MIKROE Driver Click","description":"\u003cp\u003eDriver Click features an IC with seven integrated high-current sink drivers, which can be used to drive a wide range of loads via simple parallel interface. These integrated drivers use high-efficiency MOSFETs for improved thermal performance. The DRV777 integrated motor and relay driver IC from Texas Instruments is the main active element of this Click board�. It is ideally suited for driving motors, relays, and similar inductive loads, as it features an internal free-wheeling diode for inductive kickback protection, on every channel. It operates with voltages up to 20 V, and by combining all the channels, it can sink up to 1A of current.\u003c\/p\u003e \u003cp\u003eDriver Click retains the connection flexibility of the DRV777 IC, offering a nine-pole spring terminal that can be used to implement and realize a wide range of different applications. Featuring kickback protection diodes, high impedance control inputs, input RC snubber network for improved reliability, pull-down input resistors that allow tri-stating, up to 2kV ESD protection, and more, this Click board� is a perfect solution for developing various types of motor driving applications, regardles of whether it is a stepper motor, brushed DC motor, brushless motor, or a combination of these. A special feature of this Click board� is the possibility to combine integrated drivers in parallel, allowing to sink up to 1A of current.\u003c\/p\u003e \u003cp\u003eDriver Click uses the DRV777, an integrated motor and relay driver from Texas Instruments. This IC has seven integrated current sink drivers. Each channel has a free-wheeling diode, connected to a common pin (COM) used for an inductive kickback voltage protection. This kickback voltage is typically observed at electromotors and relays, so the existence of such a protection makes this driver a good choice for driving motors, relays, and other inductive loads, which can generate back EMF.\u003c\/p\u003e \u003cp\u003eEach output is controlled by an input pin. Logic HIGH level on the input will result in the LOW state of the corresponding output, allowing a single driver to sink up to 140mA. The input logic voltage level can range between 1.8V and 5V, thus allowing a wide range of MCUs to be used. The input stage is filtered through an RC snubber filter, allowing the Click board� to be used in a noisy environment. Logic LOW on the input pin will set the output driver to a HIGH logic level, allowing up to 16V (20V absolute maximum) between the pin and the ground. While in a HIGH state, the output driver will not sink current. For this reason, the input is equipped with the weak pull-down resistor, allowing inputs to be left floating or tri-stated, ensuring that the output drivers will not accidentally drive the connected load.\u003c\/p\u003e \u003cp\u003eThe output drivers are capable of sinking up to 140mA per channel. However, the DRV777 IC allows outputs to be used in parallel, combining the current that can be sink. This allows sinking up to 1A of current when all the drivers are combined. In addition, more Click board� can be combined, allowing sinking even more current.\u003c\/p\u003e \u003cp\u003eThis Click board� is equipped with the nine-pole spring terminal. Each output is routed to the terminal, with the addition of the COM pin and GND. This pin is a common cathode pin for all the free-wheeling diodes and a special care should be taken to connect this pin to the same voltage potential as the connected load. If not connected, a permanent damage might occur to the output drivers. GND for the load should be connected to the GND input of the nine-pole spring terminal. By using the output connector, various connections can be implemented with the same Click board�. Drivers can drive relays, motors, or a combination of these. The DRV777 datasheet offers several connecting and driving solutions. It also offers more in-depth information about the IC itself.\u003c\/p\u003e \u003cp\u003eAlthough the IC uses only the 5V power rail from the mikroBUS�, the Driver Click can be freely interfaced to either 3.3V or 5V MCUs. It does not require a special jumper for the logic voltage level selection. However, it has two SMD jumpers labeled as IN6 and IN7, used to enable or disable these driver inputs. It is done so to prevent eventual interference with the UART module in some cases, as these two pins are routed to the mikroBUS� RX and TX pins. The complete pinout is contained at the table below.\u003c\/p\u003e \u003cp\u003e\u003cstrong\u003eFeatures:\u003c\/strong\u003e\u003c\/p\u003e \u003cul\u003e \u003cli\u003eInterface: GPIO\u003c\/li\u003e \u003cli\u003eCompatibility: mikroBUS�\u003c\/li\u003e \u003cli\u003eDimensions: 57.15 x 25.4mm\u003c\/li\u003e \u003cli\u003eInput Voltage: 5V\u003c\/li\u003e \u003cli\u003eThe voltage between any output pin and GND: Min. 0V, Max. 16V\u003c\/li\u003e \u003cli\u003eDriver Sink Current: Min. 0mA, Max. 140mA\u003c\/li\u003e \u003cli\u003eInput pin pull-down resistance: Min. 210k�, Typ. 300k�, Max. 390k�\u003c\/li\u003e \u003c\/ul\u003e \u003cp\u003e\u003cstrong\u003eDocuments:\u003c\/strong\u003e\u003c\/p\u003e \u003cul\u003e \u003cli\u003e\u003ca href=\"https:\/\/cdn.sparkfun.com\/assets\/c\/4\/e\/5\/2\/Schematic-19953-MIKROE_Driver_Click.pdf\"\u003eSchematic\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/cdn.sparkfun.com\/assets\/f\/c\/8\/3\/7\/drv777.pdf\"\u003eDRV777 Datasheet\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/www.mikroe.com\/mikrosdk\"\u003emikroSDK\u003c\/a\u003e\u003c\/li\u003e \u003cli\u003e\u003ca href=\"https:\/\/github.com\/MikroElektronika\/mikrosdk_click_v2\/tree\/master\/clicks\/driver\"\u003eGitHub\u003c\/a\u003e\u003c\/li\u003e \u003c\/ul\u003e","brand":"sparkfun-10","offers":[{"title":"Default Title","offer_id":40331961598037,"sku":"19953:ROB-19953:spark","price":2190.0,"currency_code":"INR","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/1034\/1611\/products\/19953_-_MIKROE_Driver_Click_2.jpg?v=1663616569","url":"https:\/\/www.tanotis.com\/products\/sparkfun-mikroe-driver-click","provider":"Tanotis","version":"1.0","type":"link"}