From Manufacturer
Introducing The Victrola Automatic Turntable
Audioengine - HD3 2 Way Wireless Bookshelf Speakers
Audioengine S8 Subwoofer Setup Video
Dust off that vinyl collection to play and listen to your records with ease using this Kit that includes the Victrola VPT-800-BLK Automatic Three-Speed Turntable with Bluetooth, satin black Audioengine HD3 Bluetooth Speaker System, and black Audioengine S8 8" 250W Subwoofer. Couple the turntable to the speakers via wired RCA or wireless Bluetooth connectivity to enjoy 2.1-channel full-range sound.
Victrola Automatic Two-Speed Turntable with Bluetooth
Listen to your favorite side of your record continuously without lifting a finger using The Automatic Turntable with Bluetooth from Victrola. The Automatic is a two-speed belt-driven turntable, featuring fully automatic operation and the unique Repeat function that perpetually plays the side of a record until you hit stop.
Automatic Turntable with Repeat Function
The Victrola Automatic lets you play your records with the simple push of a button. No fumbling with the needle or having to jump up when the record is over, simply place a record on the platter, press play, and the turntable goes to work. With the Repeat function, when the needle reches the end of the groove, the tonearm lifts and resets to the beginning, keeping the music going as long as you'd like.
This turntable can be connected to a wide array of audio input devices for playback. VINYLSTREAM Bluetooth output enables wireless streaming to compatible receivers, speakers, and headphones. A stereo RCA output is available to provide a hardwired connection that can be switched between phono and line level to connect to a home receiver or powered speakers.
Please note, if using the phono level output, it is recommended to use a grounding wire (not included) to connect the ground pin between the turntable and the external component.
- Factory-installed Audio Technica ATN3600L MM cartridge
- Removable dust cover included
- Simple push-button controls
- Easy installation of platter and belt required
Audioengine HD3 Bluetooth Speaker System (Satin Black, Pair)
Enjoy your audio from nearly any source with this pair of satin black Audioengine HD3 Bluetooth Speaker System. They feature Bluetooth with aptX HD for wireless connectivity, stereo RCA and 1/8" inputs for traditional wired devices, and a micro-USB input for a dedicated input from your computer. The HD3 has a 2-way design with two built-in, 15W per channel amplifiers. Each speaker sports a 2.75" Kevlar woofer and a 0.75" silk dome tweeter.
Connect to the HD3 any way you like: wirelessly or wired, digital or analog. Stream your music library, TIDAL, Spotify, Pandora, YouTube, etc. to the HD3 from just about anywhere in your house (within 100') without dropouts. Wireless setup is designed for simplicity and only takes about a minute. And if you're using the HD3 on your desktop, connect it with a USB cable. The USB input bypasses your computer's built-in headphone jack for an enhanced listening experience. If you're not keen on USB or wireless, you can still use any stereo RCA or 1/8" audio cable to connect.
The HD3 is expandable, so if you want deeper bass, just connect your subwoofer.
The HD3 includes a dedicated headphone output on the front panel, so you can listen without waking the neighbors. Its headphone amplifier is designed to deliver quality sound that drives even the most demanding headphones.
The HD3 features aluminum trim accents and detachable magnetic grilles designed to blend with any d?cor.
Built-in power amplifiers save space and eliminate the need to connect the HD3 to a stereo receiver or external power amp. Simply plug the left speaker into a power outlet and connect the included speaker wire from the left to the right speaker. All internal components of the HD3 are designed and tuned together for a more uniform sound than traditional separate speakers and amplifier.
The speaker cabinets, drivers, bass port designs, amplifiers, and passive crossovers are all tuned together specifically for the HD3. This is designed to provide for a more efficient system that requires less power than passive speakers and a separate integrated amplifier or similar A/V components.
Features from the Audioengine B1 aptX HD Bluetooth receiver and D1 24-bit DAC are combined in the HD3 to help make it a complete digital audio system.
The HD3 is designed to easily connect to any of your devices that have Bluetooth, but for enhanced sound quality, use a device that supports Bluetooth aptX HD. For Apple devices that don't have aptX HD, such as the iPad or iPhone, Apple generally uses the AAC codec. It sounds good as well, and you'll get the extra benefit of the upsampling 24-bit DAC.
Through signal management circuitry and antenna tuning, the HD3 offers a solution that has up to three times the range of standard Bluetooth for multi-room use with no degradation in audio quality.
The HD3 Bluetooth receiver and USB input both utilize the PCM 5102 DAC, which is designed for low-noise and high-fidelity. The PCM 5102 is used as an upsampling DAC and will pad all bit depths to 24-bit, achieving a higher signal-to-noise ratio and lower noise floor. Due to the high signal-to-noise specs of the PCM 5102, the fact that digital signal is upsampled to 24-bits ? as well as the added benefit of onboard triple-redundancy power source conversion and filtering ? the HD3 Bluetooth implementation presents low noise and low distortion characteristics with a noticeable improvement over other Bluetooth devices.
The HD3 contains a headphone amplifier based on the OPA2134 low-noise opamp. This amp is designed to provide low-impedance, high-fidelity audio and a 2V output, which can drive a wide range of headphones.
The amplifiers in the HD3 are located in the left speaker and are a class A/B analog monoblock design. This is a more traditional speaker/amplifier configuration, which is designed to provide quality audio and greater flexibility. All circuit boards for the power and preamp sections are vertically mounted for enhanced mechanical shock protection.
The HD3 uses ferrofluid-cooled silk dome tweeters with neodymium magnets. Silk tweeters are fashioned to hold up well under high power, and the edge-driven design gives a smooth response. The woofers are Kevlar-woven glass-aramid composite with rubber surrounds. Kevlar is designed for strength, so the woofer can retain its shape when being driven at high levels.
The speaker drivers in the HD3s are directly magnetically shielded.
- RCA and 1/8" audion inputs for easy connection to various audio sources, including a turntable or TV
- USB input for computer connection with up-sampling 24-bit DAC
- 0.75" thick MDF cabinets with wood veneer
Audioengine S8 8" 250W Subwoofer (Black)
Enhance the bass in your home theater system with the black Audioengine S8 8" 250W Subwoofer. It features a front-firing linear port enclosure designed to minimize excessive noise, a down-firing 8" long-throw woofer with magnetic shielding, and an MDF cabinet enclosure. This design enables the S8 to reproduce a tight "punch" at high sound levels.
The S8 also features a 250W Class D amplifier and a wide frequency response for enhanced sound quality and low distortion. It's stylish, compact 11.25" cube design will complement the flat-screen TV in your home theater setup.
Powerful 250W Class D Amplification
A 250W Class D amplifier makes this subwoofer well suited for most situations.
Front-Firing Linear Port and Down-Firing Woofer Design
This subwoofer utilizes a front-firing linear port and down-firing woofer designed to complement front surround systems and micro component systems.
Advanced Protection Circuitry
This subwoofer offers Output Current Limiting, Thermal Over-Temperature, and Power On/Off Transient Protection, which help ensure that sound reproduction will be clean and well defined.
If you decide to place this subwoofer away from your powered speakers or surround receiver, the optional Audioengine W3 wireless audio adapter offers the ability to incorporate wireless bass in your home theater system. With its plug-and-play design, the W3 sets up in minutes with no apps or software to install.
Its housing is designed with magnetic shielding, preventing undesirable interference that causes distortion.
Items Included
- Victrola Automatic Two-Speed Turntable with Bluetooth
- Dust Cover
- Platter with Belt
- Slipmat
- 45 rpm Adapter
- RCA Cable
- Power Adapter
- Limited 1-Year Manufacturer Warranty
- Audioengine HD3 Bluetooth Speaker System (Satin Black, Pair)
- 2 x Grilles
- 5' Mini-Jack Audio Cable
- 5' USB Cable
- 6.5' 16 AWG Speaker Wire
- Antenna
- Microfiber Speaker Bags
- Microfiber Cable Bag
- Microfiber Power Supply Bag
- Power Supply
- AC Power Cable
- Limited 3-Year Manufacturer Warranty
- Audioengine S8 8" 250W Subwoofer (Black)
- 1/8" Audio Cable (6.5')
- RCA Audio Cable (6.5')
- Drawstring Cable Bag
- Drawstring Subwoofer Bag
- AC Power Cord
- Limited 3-Year Manufacturer Warranty
Additional Resources
Victrola Automatic Two-Speed Turntable with Bluetooth
Inputs/Outputs
| Audio I/O |
1x 2RCA Output (Line/Phono Switchable)
|
Wireless
| Wireless |
Bluetooth 5.1
|
| Mobile App Compatible |
No
|
Power
| Power Source |
AC Adapter with Power Brick (Included)
|
| AC Input Power |
100 to 240 VAC, 50 / 60 Hz
|
| DC Input Power |
12 VDC at 0.6 A
|
| Power Consumption |
6 W
|
Physical
| Color |
Black
|
| Material of Construction |
MDF, Plastic
|
| Certifications |
FCC, IC
|
| Dimensions |
14.8 x 13.4 x 3.9" / 37.5 x 34 x 9.8 cm
|
| Weight |
7.94 lb / 3.6 kg
|
Packaging Info
| Package Weight |
8.58 lb
|
| Box Dimensions (LxWxH) |
|
All product and company names are trademarks™ or registered® trademarks of their respective holders. Use of them does not imply any affiliation with or endorsement by them.